Your HP OfficeJet Pro 8500 printer is designed to work with original HP 940 and HP 940XL ink cartridges. Only original HP C4900A, C4901A, C4902AN, C4903AN, C4904AN, C4905AN, C4906AN, C4907AN, C4908AN, C4909AN, CN065FN ink cartridges can provide the results your printer was engineered to deliver.
Thereof, How do I refill my HP OfficeJet Pro 8500 ink cartridge?
You do not need to reset the cartridges manually. All you have to do is remove the rubber plug on the top of the cart, inject ink until full, put the rubber plug back in place, reset the chip, and you are ready to go.
Accordingly, How do I clean the printhead on my HP Officejet Pro 8500a?
Cleaning the printhead contacts
- Gather the following materials: …
- Lift the carriage-access door. …
- Press and hold the * button for five seconds. …
- Unplug the power cord from the rear of the product. …
- Inside the product, lift the blue printhead latch.
How do I change the printhead on my HP Officejet Pro 8500a?
Step two: Remove the old printhead
- Open the carriage access lid.
- Touch Change Printheads on the product control panel. The carriage moves to the access area on the left side of the product. …
- Lift the printhead latch. …
- Lift the handle of the old printhead, and then use it to pull the printhead out of its slot.
Also know How do you refill HP 940 ink cartridges?
Insert the prepared syringe with needle straight into the cartridge (picture 2). Place the needle on the plastic bar inside the cartridge. Do not insert it further or else you could damage the cartridge! Fill the cartridge with ink up until 1cm below the upper edge of the cartridge, then reinsert the plug.
How often do printheads need to be replaced? Generally printheads should serve you 1.5 – 2 years before giving any problems like print quality issues. You shouldn’t need to replace them until you see a message on the printer instructing you to do so.
Can you use rubbing alcohol to clean printer heads?
The sponge end of a blocked printer head can be cleaned with only one liquid other than water. This liquid is isopropyl alcohol. Isopropyl alcohol isn’t strong enough to melt the sponge but is still strong enough to dissolve the ink inside the blocked printer head.
How do I reset my HP Officejet Pro 8500a Plus?
For a reset with the HP 8500 Pro printer turned off, press the On / Off button to turn off the printer. Then press the on / off button again and hold your finger on the pressed button for five seconds. The display initially remains black.
How do I reset my HP 940 ink cartridge?
After installing all four ink cartridges, retest printer. 5. If problem continues, then we suggest you press and hold the reset button on the printer for five seconds… this will reset the cartridge’s smart chip, and may correct the current ‘interface’ issue.
Is it worth replacing a print head?
If everything is working fine and you are happy it is worth the cost. If you really want a better printer or a printer with different abilities and your present printer is a few years old, and you find a new printer that is a great buy with new features YOU WILL USE then save the printhead money go new!
Is it worth fixing a HP printer?
As much as you may love your HP printer, you don’t want to spend more than it is worth repairing it! As a general rule, if your HP printer cost less than $200 new (and you don’t have a surplus of ink or toner cartridges), you may be better off looking at replacement options.
How do I know if my print head is bad?
Place the print head in a saucer full of isopropyl alcohol and let it soak overnight. If the printout is still spotty, has lines or doesn’t print at all, then the head is bad. If it is not removable, you have to rely on Steps 1 through 3 to determine if it is permanently damaged.
Can I use Windex to clean printer heads?
Windex consists of around 50% ammonia which is the key ingredient for cleaning the printhead. Simply remove the cartridges and spray some Windex in the offending holes where the ink flows into the printhead itself.
How do I reset my HP Officejet Pro 8210 to factory settings?
From the home screen on the printer control panel, swipe down to open the Dashboard, and then touch the Setup icon . Swipe up on the display, and then touch Printer Maintenance. Touch Restore, and then touch Restore Factory Default. Touch Continue on the confirmation message.
How do I reset my HP Officejet Pro Premier?
Press and hold # and 3 while plugging in the power cord
to the HP All-in-One.
…
These models have a touch-screen display.
- Touch the Setup ( ) icon.
- Scroll to and touch Tools.
- Scroll to and touch Restore Factory Defaults. A Defaults Restored message displays.
- Press the Cancel button to return to the main menu.
Why does my printer say low ink when I refill it?
The message is intended as a warning so you can have a replacement cartridge available and avoid possible printing delays. … If the printer is using a refilled or remanufactured cartridge, the ‘Low on Ink’ message might be inaccurate or display even if the cartridge is not low on ink.
How do I override my HP ink cartridge expiration date?
With these caveats and your budget in mind, overriding the timer is a simple and straightforward procedure.
- Observe the indicator lights on the printer. …
- Press and hold down the “Power” button while you press the “Resume” button three times. …
- Continue printing until your cartridge runs out of ink.
How much does it cost to replace an HP printhead?
HP recommends that consumers buy a completely new print head if resetting and cleaning do not work, providing the part number for the printhead and a conveniently placed link that directs consumers to the HP parts website. The price for a new printhead from HP is $120.
How often should I clean printer heads?
What if my printer still isn’t working? If you’re still experiencing quality issues or printhead errors, then there may be other problems at play. Before taking any other actions, it’s recommended that you clean the printhead and ink cartridges four or five more times.
Can printhead be fixed?
Clogged print heads are the result of dried-up ink from lack of use, and can lead to patchy or erroneous printing. You can usually fix clogged print heads with your printer’s built-in self-cleaning software, though you may have to clean the print heads manually if that doesn’t work.
Is it cheaper to fix a printer or buy a new one?
A good rule of thumb is, if the printer repair costs more than half of what it would cost to get a new machine, then perhaps you should buy a new one. … Here are some additional questions to ask before deciding if printer repair is a good route.
Can you leave a wireless printer on all the time?
You can leave the Printer ON all the time and it is safe. You can setup the Energy Saving Mode to put the Printer in Sleep Mode when not in use.
What is the average life of a printer?
The average lifespan of a printer is around 3-5 years. With proper upkeep and maintenance, some printers can last longer, but eventually your machine will need an upgrade.
Don’t forget to share this post!